CubeMon-Vue-Demo-STM32F407VGT6U
Macros
stm32f4xx_hal_conf.h File Reference

HAL configuration template file. This file should be copied to the application folder and renamed to stm32f4xx_hal_conf.h. More...

#include "stm32f4xx_hal_rcc.h"
#include "stm32f4xx_hal_gpio.h"
#include "stm32f4xx_hal_exti.h"
#include "stm32f4xx_hal_dma.h"
#include "stm32f4xx_hal_cortex.h"
#include "stm32f4xx_hal_adc.h"
#include "stm32f4xx_hal_dac.h"
#include "stm32f4xx_hal_flash.h"
#include "stm32f4xx_hal_i2c.h"
#include "stm32f4xx_hal_iwdg.h"
#include "stm32f4xx_hal_pwr.h"
#include "stm32f4xx_hal_tim.h"

Go to the source code of this file.

Macros

#define HAL_MODULE_ENABLED
 This is the list of modules to be used in the HAL driver.
 
#define HAL_ADC_MODULE_ENABLED
 
#define HAL_DAC_MODULE_ENABLED
 
#define HAL_I2C_MODULE_ENABLED
 
#define HAL_IWDG_MODULE_ENABLED
 
#define HAL_TIM_MODULE_ENABLED
 
#define HAL_GPIO_MODULE_ENABLED
 
#define HAL_EXTI_MODULE_ENABLED
 
#define HAL_DMA_MODULE_ENABLED
 
#define HAL_RCC_MODULE_ENABLED
 
#define HAL_FLASH_MODULE_ENABLED
 
#define HAL_PWR_MODULE_ENABLED
 
#define HAL_CORTEX_MODULE_ENABLED
 
#define HSE_VALUE   25000000U
 Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). More...
 
#define HSE_STARTUP_TIMEOUT   100U
 
#define HSI_VALUE   ((uint32_t)16000000U)
 Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). More...
 
#define LSI_VALUE   32000U
 Internal Low Speed oscillator (LSI) value. More...
 
#define LSE_VALUE   32768U
 External Low Speed oscillator (LSE) value. More...
 
#define LSE_STARTUP_TIMEOUT   5000U
 
#define EXTERNAL_CLOCK_VALUE   12288000U
 External clock source for I2S peripheral This value is used by the I2S HAL module to compute the I2S clock source frequency, this source is inserted directly through I2S_CKIN pad. More...
 
#define VDD_VALUE   3300U
 This is the HAL system configuration section. More...
 
#define TICK_INT_PRIORITY   15U
 
#define USE_RTOS   0U
 
#define PREFETCH_ENABLE   1U
 
#define INSTRUCTION_CACHE_ENABLE   1U
 
#define DATA_CACHE_ENABLE   1U
 
#define USE_HAL_ADC_REGISTER_CALLBACKS   0U /* ADC register callback disabled */
 
#define USE_HAL_CAN_REGISTER_CALLBACKS   0U /* CAN register callback disabled */
 
#define USE_HAL_CEC_REGISTER_CALLBACKS   0U /* CEC register callback disabled */
 
#define USE_HAL_CRYP_REGISTER_CALLBACKS   0U /* CRYP register callback disabled */
 
#define USE_HAL_DAC_REGISTER_CALLBACKS   0U /* DAC register callback disabled */
 
#define USE_HAL_DCMI_REGISTER_CALLBACKS   0U /* DCMI register callback disabled */
 
#define USE_HAL_DFSDM_REGISTER_CALLBACKS   0U /* DFSDM register callback disabled */
 
#define USE_HAL_DMA2D_REGISTER_CALLBACKS   0U /* DMA2D register callback disabled */
 
#define USE_HAL_DSI_REGISTER_CALLBACKS   0U /* DSI register callback disabled */
 
#define USE_HAL_ETH_REGISTER_CALLBACKS   0U /* ETH register callback disabled */
 
#define USE_HAL_HASH_REGISTER_CALLBACKS   0U /* HASH register callback disabled */
 
#define USE_HAL_HCD_REGISTER_CALLBACKS   0U /* HCD register callback disabled */
 
#define USE_HAL_I2C_REGISTER_CALLBACKS   0U /* I2C register callback disabled */
 
#define USE_HAL_FMPI2C_REGISTER_CALLBACKS   0U /* FMPI2C register callback disabled */
 
#define USE_HAL_FMPSMBUS_REGISTER_CALLBACKS   0U /* FMPSMBUS register callback disabled */
 
#define USE_HAL_I2S_REGISTER_CALLBACKS   0U /* I2S register callback disabled */
 
#define USE_HAL_IRDA_REGISTER_CALLBACKS   0U /* IRDA register callback disabled */
 
#define USE_HAL_LPTIM_REGISTER_CALLBACKS   0U /* LPTIM register callback disabled */
 
#define USE_HAL_LTDC_REGISTER_CALLBACKS   0U /* LTDC register callback disabled */
 
#define USE_HAL_MMC_REGISTER_CALLBACKS   0U /* MMC register callback disabled */
 
#define USE_HAL_NAND_REGISTER_CALLBACKS   0U /* NAND register callback disabled */
 
#define USE_HAL_NOR_REGISTER_CALLBACKS   0U /* NOR register callback disabled */
 
#define USE_HAL_PCCARD_REGISTER_CALLBACKS   0U /* PCCARD register callback disabled */
 
#define USE_HAL_PCD_REGISTER_CALLBACKS   0U /* PCD register callback disabled */
 
#define USE_HAL_QSPI_REGISTER_CALLBACKS   0U /* QSPI register callback disabled */
 
#define USE_HAL_RNG_REGISTER_CALLBACKS   0U /* RNG register callback disabled */
 
#define USE_HAL_RTC_REGISTER_CALLBACKS   0U /* RTC register callback disabled */
 
#define USE_HAL_SAI_REGISTER_CALLBACKS   0U /* SAI register callback disabled */
 
#define USE_HAL_SD_REGISTER_CALLBACKS   0U /* SD register callback disabled */
 
#define USE_HAL_SMARTCARD_REGISTER_CALLBACKS   0U /* SMARTCARD register callback disabled */
 
#define USE_HAL_SDRAM_REGISTER_CALLBACKS   0U /* SDRAM register callback disabled */
 
#define USE_HAL_SRAM_REGISTER_CALLBACKS   0U /* SRAM register callback disabled */
 
#define USE_HAL_SPDIFRX_REGISTER_CALLBACKS   0U /* SPDIFRX register callback disabled */
 
#define USE_HAL_SMBUS_REGISTER_CALLBACKS   0U /* SMBUS register callback disabled */
 
#define USE_HAL_SPI_REGISTER_CALLBACKS   0U /* SPI register callback disabled */
 
#define USE_HAL_TIM_REGISTER_CALLBACKS   0U /* TIM register callback disabled */
 
#define USE_HAL_UART_REGISTER_CALLBACKS   0U /* UART register callback disabled */
 
#define USE_HAL_USART_REGISTER_CALLBACKS   0U /* USART register callback disabled */
 
#define USE_HAL_WWDG_REGISTER_CALLBACKS   0U /* WWDG register callback disabled */
 
#define MAC_ADDR0   2U
 Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code.
 
#define MAC_ADDR1   0U
 
#define MAC_ADDR2   0U
 
#define MAC_ADDR3   0U
 
#define MAC_ADDR4   0U
 
#define MAC_ADDR5   0U
 
#define ETH_RX_BUF_SIZE   ETH_MAX_PACKET_SIZE /* buffer size for receive */
 
#define ETH_TX_BUF_SIZE   ETH_MAX_PACKET_SIZE /* buffer size for transmit */
 
#define ETH_RXBUFNB   4U /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
 
#define ETH_TXBUFNB   4U /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
 
#define DP83848_PHY_ADDRESS   0x01U
 
#define PHY_RESET_DELAY   0x000000FFU
 
#define PHY_CONFIG_DELAY   0x00000FFFU
 
#define PHY_READ_TO   0x0000FFFFU
 
#define PHY_WRITE_TO   0x0000FFFFU
 
#define PHY_BCR   ((uint16_t)0x0000U)
 
#define PHY_BSR   ((uint16_t)0x0001U)
 
#define PHY_RESET   ((uint16_t)0x8000U)
 
#define PHY_LOOPBACK   ((uint16_t)0x4000U)
 
#define PHY_FULLDUPLEX_100M   ((uint16_t)0x2100U)
 
#define PHY_HALFDUPLEX_100M   ((uint16_t)0x2000U)
 
#define PHY_FULLDUPLEX_10M   ((uint16_t)0x0100U)
 
#define PHY_HALFDUPLEX_10M   ((uint16_t)0x0000U)
 
#define PHY_AUTONEGOTIATION   ((uint16_t)0x1000U)
 
#define PHY_RESTART_AUTONEGOTIATION   ((uint16_t)0x0200U)
 
#define PHY_POWERDOWN   ((uint16_t)0x0800U)
 
#define PHY_ISOLATE   ((uint16_t)0x0400U)
 
#define PHY_AUTONEGO_COMPLETE   ((uint16_t)0x0020U)
 
#define PHY_LINKED_STATUS   ((uint16_t)0x0004U)
 
#define PHY_JABBER_DETECTION   ((uint16_t)0x0002U)
 
#define PHY_SR   ((uint16_t)0x10U)
 
#define PHY_SPEED_STATUS   ((uint16_t)0x0002U)
 
#define PHY_DUPLEX_STATUS   ((uint16_t)0x0004U)
 
#define USE_SPI_CRC   0U
 
#define assert_param(expr)   ((void)0U)
 Include module's header file.
 

Detailed Description

HAL configuration template file. This file should be copied to the application folder and renamed to stm32f4xx_hal_conf.h.

Author
MCD Application Team
Attention

Copyright (c) 2017 STMicroelectronics. All rights reserved.

This software is licensed under terms that can be found in the LICENSE file in the root directory of this software component. If no LICENSE file comes with this software, it is provided AS-IS.

Macro Definition Documentation

◆ EXTERNAL_CLOCK_VALUE

#define EXTERNAL_CLOCK_VALUE   12288000U

External clock source for I2S peripheral This value is used by the I2S HAL module to compute the I2S clock source frequency, this source is inserted directly through I2S_CKIN pad.

Value of the External audio frequency in Hz

◆ HSE_STARTUP_TIMEOUT

#define HSE_STARTUP_TIMEOUT   100U

Time out for HSE start up, in ms

◆ HSE_VALUE

#define HSE_VALUE   25000000U

Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL).

Value of the External oscillator in Hz

◆ HSI_VALUE

#define HSI_VALUE   ((uint32_t)16000000U)

Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL).

Value of the Internal oscillator in Hz

◆ LSE_STARTUP_TIMEOUT

#define LSE_STARTUP_TIMEOUT   5000U

Time out for LSE start up, in ms

◆ LSE_VALUE

#define LSE_VALUE   32768U

External Low Speed oscillator (LSE) value.

< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature. Value of the External Low Speed oscillator in Hz

◆ LSI_VALUE

#define LSI_VALUE   32000U

Internal Low Speed oscillator (LSI) value.

LSI Typical Value in Hz

◆ PHY_AUTONEGO_COMPLETE

#define PHY_AUTONEGO_COMPLETE   ((uint16_t)0x0020U)

Auto-Negotiation process completed

◆ PHY_AUTONEGOTIATION

#define PHY_AUTONEGOTIATION   ((uint16_t)0x1000U)

Enable auto-negotiation function

◆ PHY_BCR

#define PHY_BCR   ((uint16_t)0x0000U)

Transceiver Basic Control Register

◆ PHY_BSR

#define PHY_BSR   ((uint16_t)0x0001U)

Transceiver Basic Status Register

◆ PHY_DUPLEX_STATUS

#define PHY_DUPLEX_STATUS   ((uint16_t)0x0004U)

PHY Duplex mask

◆ PHY_FULLDUPLEX_100M

#define PHY_FULLDUPLEX_100M   ((uint16_t)0x2100U)

Set the full-duplex mode at 100 Mb/s

◆ PHY_FULLDUPLEX_10M

#define PHY_FULLDUPLEX_10M   ((uint16_t)0x0100U)

Set the full-duplex mode at 10 Mb/s

◆ PHY_HALFDUPLEX_100M

#define PHY_HALFDUPLEX_100M   ((uint16_t)0x2000U)

Set the half-duplex mode at 100 Mb/s

◆ PHY_HALFDUPLEX_10M

#define PHY_HALFDUPLEX_10M   ((uint16_t)0x0000U)

Set the half-duplex mode at 10 Mb/s

◆ PHY_ISOLATE

#define PHY_ISOLATE   ((uint16_t)0x0400U)

Isolate PHY from MII

◆ PHY_JABBER_DETECTION

#define PHY_JABBER_DETECTION   ((uint16_t)0x0002U)

Jabber condition detected

◆ PHY_LINKED_STATUS

#define PHY_LINKED_STATUS   ((uint16_t)0x0004U)

Valid link established

◆ PHY_LOOPBACK

#define PHY_LOOPBACK   ((uint16_t)0x4000U)

Select loop-back mode

◆ PHY_POWERDOWN

#define PHY_POWERDOWN   ((uint16_t)0x0800U)

Select the power down mode

◆ PHY_RESET

#define PHY_RESET   ((uint16_t)0x8000U)

PHY Reset

◆ PHY_RESTART_AUTONEGOTIATION

#define PHY_RESTART_AUTONEGOTIATION   ((uint16_t)0x0200U)

Restart auto-negotiation function

◆ PHY_SPEED_STATUS

#define PHY_SPEED_STATUS   ((uint16_t)0x0002U)

PHY Speed mask

◆ PHY_SR

#define PHY_SR   ((uint16_t)0x10U)

PHY status register Offset

◆ TICK_INT_PRIORITY

#define TICK_INT_PRIORITY   15U

tick interrupt priority

◆ VDD_VALUE

#define VDD_VALUE   3300U

This is the HAL system configuration section.

Value of VDD in mv